dbl101g thru dbl107g single phase 1.0 amp. glass passivated bridge rectifiers voltage range 50 to 1000 volts current 1.0 ampere features ul recognized file # e-96005 glass passivated junction ideal for printed circuit board reliable low cost construction utilizing molded plastic technique high temperature soldering guaranteed: 260 / 10 seconds / 0.375? ( 9.5mm ) lead length at 5 lbs., ( 2.3 kg ) tension small size, simple installation leads solderable per mil-std-202, method 208 high surge current capability dbl dbls dimensions in inches and (millimeters) maximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% dbl 101g dbl 102g dbl 103g dbl 104g dbl 105g dbl 106g dbl 107g type number dbls 101g dbls 102g dbls 103g dbls 104g dbls 105g dbls 106g dbls 107g units maximum recurrent peak reverse voltage 50 100 200 400 600 800 1000 v maximum rms voltage 35 70 140 280 420 560 700 v maximum dc blocking voltage 50 100 200 400 600 800 1000 v maximum average forward rectified current @t a = 40 1.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) 50 a maximum instantaneous forward voltage @ 1.0a 1.1 v maximum dc reverse current @ t a =25 at rated dc blocking voltage @ t a =125 10 500 ua ua typical thermal resistance (note 1) r ja r jl 40 15 /w operating temperature range t j -55 to +150 storage temperature range t stg -55 to +150 note: 1. thermal resistance from junction to ambient and from junction to lead mounted on p.c.b. with 0.47 x 0.47? (12 x 12mm) copper pads. 2. dbs for surface mount package. .404(10.3) .386(9.80) .255(6.5) .245(6.2) .013(0.33) .0088(0.22) .013(0.33) .003(0.076) .060(1.53) .040(1.02) .205(5.2) .195(5.0) .047(1.20) .040(1.02) .335(8.51) .320(8.13) 0 45 .102(2.60) .094(2.40) .315(8.0) .285(7.24) .335(8.51) .320(8.12) .102(2.60) .094(2.40) .255(6.5) .245(6.2) .045(1.14) .035(0.89) .205(5.2) .195(5.0) .023(0.58) .018(0.46) .075(1.90) .055(1.39) .185(4.69) .150(3.81) .08(2.03) .05(1.27) .350(8.9) .300(7.6) .013(0.33) .0088(0.22)
ratings and characteristic curves (dbl101g thru dbl107g) fig.3- typical reverse characteristics per bridge element instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 100 .01 .10 1.0 10 percent of rated peak reverse voltage. (%) tj=125 c 0 tj=25 c 0 fig.4- typical forward characteristics per bridge element instantaneous for ward current . (a) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.01 0.1 1 10 forward voltage. (v) tj=25 c pulse width-300 s 2% duty cycle 0 fig.5- typical junction capacitance per bridge element capacitance.(pf) 1.0 10 100 1 10 100 reverse voltage. (v) tj=25 c f=1.0mhz vsig=50mvp-p 0 fig.2- maximum non-repetitive peak forward surge current peak for ward surge current . (a) 1 2 4 6 10 20 100 60 40 0 10 40 60 50 20 30 number of cycles at 60hz single sine - wave (jedec method) tj=25 c 0 fig.1- maximum derating curve for output rectified current average for ward current . (a) 20 40 60 80 100 120 140 150 0 0.5 1.0 ambient temperature. ( c) o 60hz resistive or inductive load copper pauls .51" x .51" (13mm x 13mm) .06" (1.5mm) pcb
|
